Semitransparent Sb₂S₃ thin film solar cells by ultrasonic spray pyrolysis for use in solar windows

• Jako S. Eensalu,
• Atanas Katerski,
• Erki Kärber,
• Lothar Weinhardt,
• Monika Blum,
• Clemens Heske,
• Wanli Yang,
• Ilona Oja Acik and
• Malle Krunks

Beilstein J. Nanotechnol. 2019, 10, 2396–2409, doi:10.3762/bjnano.10.230

• techniques are the high energy demand and the need for batch processing, which inflates production costs. As a potent solution-based chemical deposition method, ultrasonic chemical spray pyrolysis (USP) is capable of rapid, area-scalable, roll-to-roll and low-cost in-air deposition of Sb2S3 layers without

Uniform Sb₂S₃ optical coatings by chemical spray method

• Jako S. Eensalu,
• Atanas Katerski,
• Erki Kärber,
• Ilona Oja Acik,
• Arvo Mere and
• Malle Krunks

Beilstein J. Nanotechnol. 2019, 10, 198–210, doi:10.3762/bjnano.10.18

• controllable in-air growth of continuous, uniform, polycrystalline Sb2S3 absorber layers has not yet been accomplished. This could be achieved with chemical spray pyrolysis, a robust chemical method for deposition of thin films. We applied a two-stage process to produce continuous Sb2S3 optical coatings with

• chemical bath deposition (CBD) [3][4], spin coating [5], atomic layer deposition (ALD) [6] or chemical spray pyrolysis (CSP) [7] method, has been applied in extremely thin absorber (ETA) solar cells due to its excellent absorption coefficient in the visible light spectrum (1.8 × 105 cm−1 at 450 nm) [1][2

• structured solar cells [8]. Planar ≈1.7 eV absorber layers can be applied in semitransparent solar cells as well as in tandem solar cells. Chemical spray pyrolysis (CSP) is a robust and industrially scalable chemical method for rapid deposition of thin films [9]. Our research group first investigated spray

Sb₂S₃ grown by ultrasonic spray pyrolysis and its application in a hybrid solar cell

• Erki Kärber,
• Atanas Katerski,
• Ilona Oja Acik,
• Arvo Mere,
• Valdek Mikli and
• Malle Krunks

Beilstein J. Nanotechnol. 2016, 7, 1662–1673, doi:10.3762/bjnano.7.158

• Materials Science, Tallinn University of Technology, Ehitajate tee 5, 19086 Tallinn, Estonia 10.3762/bjnano.7.158 Abstract Chemical spray pyrolysis (CSP) is a fast wet-chemical deposition method in which an aerosol is guided by carrier gas onto a hot substrate where the decomposition of the precursor

• /cm2, a fill factor of 42% and a conversion efficiency of 1.3%. Conversion efficiencies up to 1.9% were obtained from solar cells with smaller areas. Keywords: absorber; chemical spray pyrolysis (CSP); hybrid solar cell; stibnite (Sb2S3); ultrasonic atomization; Introduction A solution-based

• efficiencies of up to 2.3% when based on planar TiO2 [12] and 6.4% [20] when based on mesoporous TiO2. Spin coating is a simple technique and seems attractive for the deposition of oxide-free Sb2S3 absorber. However, an annealing stage at 300 °C in inert gas atmosphere is involved. Chemical spray pyrolysis

Low-cost plasmonic solar cells prepared by chemical spray pyrolysis

• Erki Kärber,
• Atanas Katerski,
• Ilona Oja Acik,
• Valdek Mikli,
• Arvo Mere,
• Ilmo Sildos and
• Malle Krunks

Beilstein J. Nanotechnol. 2014, 5, 2398–2402, doi:10.3762/bjnano.5.249

• planar ZnO were prepared entirely by chemical spray pyrolysis. Au nanoparticles (Au-NPs) were formed via thermal decomposition of a gold(III) chloride trihydrate (HAuCl4·3H2O) precursor by spraying 2 mmol/L of the aqueous precursor solution onto a substrate held at 260 °C. Current–voltage scans and

• % increase (from 4.6 to 7.5 mA/cm2) of the short-circuit current density was observed when 2.5 mL of the precursor solution was deposited onto the rear side of the solar cell. Keywords: Au nanoparticles; chemical spray pyrolysis; extremely thin absorber; plasmon resonance; solar cell; Introduction The cost

• , while providing a technologically simple method for solar cell production. Chemical spray pyrolysis (CSP) is a simple method to produce thin semiconductor oxide- and sulphide layers and metal nanoparticles (NPs) via thermal decomposition of metal precursor salts. CuInS2 (CIS) is a semiconductor material